--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/level2/modules/krnp4_regdump.asm	Wed Jan 08 03:40:21 2003 +0000
@@ -0,0 +1,325 @@
+********************************************************************
+* OS9p4 - User Register Dump System Call for OS9 Level Two
+*
+* $Id$
+*
+* Copyright February,1989 by Ron Lammardo
+*
+* This system call can be used in an application program to dump the
+* current contents of all user registers in Hex,Decimal,Binary and Ascii 
+* (Registers "A" and "B" Only). This module MUST be present in the
+* bootfile. If no OS9P3 module is found,change the "mname" and "nextname"
+* as appropriate.
+*
+* If there is a conflict with the code used for this system called, it can
+* be changed by resetting the equate at "F$RegDmp"
+*
+* NOTE: All registers EXCEPT 'CC' are preserved....OS9 internally resets
+*       the condition code register upon service call exit.
+*
+* Ed.    Comments                                       Who YY/MM/DD
+* ------------------------------------------------------------------
+*   1    Started                                        RL  89/02/??
+
+         nam   os9p4 
+         ttl   User Register Dump System Call for OS9 Level Two
+
+         ifp1  
+         use   defsfile
+         endc  
+
+tylg     set   systm+objct
+atrv     set   reent+revision
+revision set   1
+edition  set   1
+
+         mod   eom,name,tylg,atrv,start,0
+
+name     fcs   /OS9p4/    name of this module
+         fcb   edition
+
+svctabl  fcb   F$RegDmp   F$RegDmp code
+         fdb   regdmp-*-2 offset to actual code
+         fcb   $80        end of table
+
+start    leay  <svctabl,pcr point to service table
+         os9   F$SSvc     insert the new op code in the table
+         lda   #tylg      get next module type (same as this one!)
+         leax  <nextname,pcr get address of next module name
+         os9   F$Link     attempt to link to it
+         bcs   endsetup   no good...skip this
+         jsr   ,y         else go execute it
+endsetup rts              return back to previous module
+
+nextname fcc   /OS9P5/    next module name to link to
+         fcb   $0d
+
+regdmp   equ   *
+         IFNE  H6309
+         pshs  cc,a,b,e,f,dp,x,y,u save all registers
+         ELSE
+         pshs  cc,a,b,dp,x,y,u save all registers
+         ENDC
+         tfr   u,y        transfer addresses
+         leas  -60,s      back up for some variable storage
+         leau  4,s        buffer starts here
+         clr   ,u+        set flag to print ascii char
+         lda   #$20       get a space
+         ldb   #50        number of chars to clear
+         tfr   u,x        set register for loop
+
+clrloop  sta   ,x+        initialize a space
+         decb             decrement counter
+         bne   clrloop    if more..loop back & clear another
+         lbsr  reg060     send a <cr>
+         leax  reg080,pcr point to start of control table
+         clra             clear msb of register
+         ldb   R$A,y      get register from stack
+         bsr   reg000     dump register A
+         ldb   R$B,y      get register from stack
+         bsr   reg000     dump register B
+         IFNE  H6309
+         ldb   R$E,y      get register from stack
+         bsr   reg000     dump register E
+         ldb   R$F,y      get register from stack
+         bsr   reg000     dump register F
+         ENDC
+         inc   -1,u       turn off ascii char print flag
+         ldd   R$X,y      get register from stack
+         bsr   reg000     dump register X
+         ldd   R$Y,y      get register from stack
+         bsr   reg000     dump regisetr Y
+         ldd   R$U,y      get register from stack
+         bsr   reg000     dump register U
+         ldb   R$CC,y     get register from stack
+         bsr   reg000     dump register CC
+         ldb   R$DP,y     get register from stack
+         bsr   reg000     dump register DP
+         ldd   R$PC,y     get user Task Number
+         bsr   reg000     dump register PC
+         ldy   <D.Proc    get address of users process descriptor
+         ldd   P$SP,y     get users stack address
+         IFNE  H6309
+         addd  #14        add on for registers which were saved
+         ELSE
+         addd  #12        add on for registers which were saved
+         ENDC
+         bsr   reg000     dump register S
+         lbsr  reg060     send a <CR>
+         leas  60,s       restore stack pointer
+         IFNE  H6309
+         puls  cc,a,b,e,f,dp,x,y,u,pc restore all registers and return
+         ELSE
+         puls  cc,a,b,dp,x,y,u,pc restore all registers and return
+         ENDC
+
+* Dump a register in "D"
+* X = Control Table Location
+* U = Output buffer Location
+
+reg000   pshs  y          save y register
+         tfr   d,y        register in y
+         lda   ,x         # of bytes
+         leax  3,x        point past table entry
+         pshs  a,x,y,u    save registers
+         ldd   -2,x       get register name
+         std   ,u++       move to buffer
+         ldd   #"=$       get chars
+         std   ,u++       move to buffer
+         ldd   3,s        get reg
+         lbsr  gethex     convert to hex
+         tst   0,s        1 byte ?
+         bne   reg010     no...skip this
+         ldd   2,u        get 2 lsb's
+         std   ,u         store in msb's
+         ldd   #$2020     get two blanks
+         std   2,u        store in lsb's
+
+reg010   ldd   #$2023     get a space and  "#"
+         std   4,u        move in two spaces
+         leau  6,u        point to start of decimal output buffer
+         ldd   3,s        get register
+         lbsr  getdec     convert to decimal
+         tst   0,s        is it one byte
+         bne   reg020     no..skip this
+         ldd   2,u        else get third & fourth chars
+         std   ,u         store as first two
+         lda   4,u        get fifth char
+         sta   2,u        store as third
+         ldd   #$2020     get two spaces
+         std   3,u        store as 4th & 5th chars
+
+reg020   ldd   #$2025     get a blank & "%"
+         std   5,u        move it to buffer
+         leau  7,u        point to start of binary output area
+         tfr   a,b        space in 'b'
+         std   16,u       space out ascii char
+         ldd   3,s        get register
+         bsr   getbin     convert to binary
+         tst   0,s        check byte count
+         bne   reg040     skip if two bytes
+         ldb   #8         loop counter
+
+reg030   lda   8,u        get two chars from second 8 digits
+         sta   ,u+        store in first 8 digits
+         lda   #$20       get two blanks
+         sta   7,u        store in second 8 digits
+         decb             decrement counter
+         bne   reg030     loop back if not done
+         leau  -8,u       back up to beginning of binary digit output
+         ldb   4,s        get lsb of register
+         tst   -18,u      check if we want to print ascii char
+         bne   reg040     nope..skip this
+         cmpb  #$20       compare char with space
+         blo   reg040     if lower..skip this
+         cmpb  #'z        compare with last alpha char
+         bhi   reg040     if higher..skip this
+         stb   17,u       else store the char
+
+reg040   lda   #C$CR      get a <cr>
+         sta   18,u       and store it
+         leax  -17,u      back up to buffer start
+         bsr   reg070     send it
+         clra             clear msb for next reg
+         puls  b,x,y,u    restore registers
+         puls  y,pc       restore y & return
+
+reg050   fcb   $0d
+
+reg060   leax  <reg050,pcr point to <cr>
+
+reg070   pshs  x,y,u,a,b  save registers
+         ldy   <D.Proc    get process descriptor address
+         lda   P$Path+2,y get user error path number
+         pshs  a          save it
+         ldu   P$SP,y     get user stack address
+         leau  -50,u      back off to make room
+         lda   <D.SysTsk  get system task number
+         ldb   P$Task,y   get users task number
+         ldy   #40        chars to move
+         os9   F$Move     move from system to user space
+         tfr   u,x        restore buffer address
+         puls  a          restore user error path number
+         os9   I$WritLn   send it
+         puls  x,y,u,a,b,pc restore registers & return
+
+* Control  Table - Format is :
+*      Byte count    (0=1,1=2)
+*      Register name (Two chars)
+
+reg080   fcb   0
+         fcc   /a /
+         fcb   0
+         fcc   /b /
+         IFNE  H6309
+         fcb   0
+         fcc   /e /
+         fcb   0
+         fcc   /f /
+         ENDC
+         fcb   1
+         fcc   /x /
+         fcb   1
+         fcc   /y /
+         fcb   1
+         fcc   /u /
+         fcb   0
+         fcc   /cc/
+         fcb   0
+         fcc   /dp/
+         fcb   1
+         fcc   /pc/
+         fcb   1
+         fcc   /s /
+
+
+* Convert "D" to binary digits in buffer "U"
+
+getbin   pshs  u,b        save 'u', second byte of register
+         bsr   bin010     convert first byte
+         puls  a          get second byte
+         bsr   bin010     convert it
+         puls  u,pc       restore 'u' and return
+
+bin010   bita  #%10000000 check bit
+         bsr   bin020     print result
+         bita  #%01000000
+         bsr   bin020
+         bita  #%00100000
+         bsr   bin020
+         bita  #%00010000
+         bsr   bin020
+         bita  #%00001000
+         bsr   bin020
+         bita  #%00000100
+         bsr   bin020
+         bita  #%00000010
+         bsr   bin020
+         bita  #%00000001
+
+bin020   beq   bin030     skip this if bit was set
+         ldb   #'1        else get an ascii '1'
+         bra   bin040     skip next
+
+bin030   ldb   #'0        bit not set...get an ascii '0'
+
+bin040   stb   ,u+        store the ascii char
+         rts   
+
+* Convert "D" to 4 hex digits in buffer "U"
+
+gethex   pshs  u,b        save 'u',second register byte
+         bsr   gth010     convert first byte
+         puls  a          restore second byte
+         bsr   gth010     convert it
+         puls  u,pc       restore 'u' and return
+
+gth010   pshs  a          save the byte
+         lsra             shift left 4 bits to right
+         lsra  
+         lsra  
+         lsra  
+         bsr   gth020     convert to hex digit
+         puls  a          restore the byte
+         anda  #$0f       strip off high 4 digits
+
+gth020   adda  #'0        make it ascii
+         cmpa  #$3a       is it a letter
+         blt   gth030     nope..skip this
+         adda  #7         else add bias
+
+gth030   sta   ,u+        store the ascii character
+         rts              return
+
+* Convert "D" to 5 decimal digits in buffer at "U"
+getdec   pshs  x,y,u      save registers
+         ldx   #10000     get decimal number for subtraction
+         bsr   gtd010     get the decimal digit
+         ldx   #01000
+         bsr   gtd010
+         ldx   #00100
+         bsr   gtd010
+         ldx   #00010
+         bsr   gtd010
+         ldx   #00001
+         bsr   gtd010
+         puls  x,y,u,pc   restore registers & return
+
+gtd010   pshs  x,a        save x register & extra byte
+         clr   ,s         clear counter
+
+gtd020   cmpd  1,s        compare 'd' with 'x' on stack
+         blo   gtd030     less...skip this
+         subd  1,s        else subtract number on stack
+         inc   ,s         increment digit counter
+         bra   gtd020     and loop back
+
+gtd030   std   1,s        save remainder of number
+         ldb   ,s+        get counter
+         addb  #$30       make it ascii
+         stb   ,u+        and move it as output
+         puls  d,pc       restore remainder & return
+
+         emod  
+eom      equ   *
+         end